Brake pads are usable with retaining clips. In fact, loops are mostly found at the surface of the pads so as to enhance the attachment of the retaining clips to the caliper pins.
Retaining clips are also known as anti-rattle clips. All these augments the rigidity of brake pads onto brake discs.
However, in this article, we would be highlighting the tips to inculcate while installing retaining clips with brake pads.
Notwithstanding, let’s begin by enumerating what both are basically used for. Spring clips are often used in tightening brake pads onto calipers.
Moreover, this tends to augments the firmness of the brake pad onto the brake disk. That’s awesome, right? Of course!
However, what this article, how to install brake pad retaining clip, tend to help you with is to educate you on how to install brake pads using retaining clips with it.
Therefore, let’s check out the systematic steps to practice.
8 Things to consider about How to Install Brake Pad Retaining Clip:
1. Make the Right Purchase
Know the size of the brake pads and retaining clips that are apt for your automobile. However, the best way to do this is to take note of the specification that is inscribed on a particular product.
Find out also whether your car model is workable with it. Nonetheless, brake pads that are made of metal, semi-metals are used for race cars, newly made cars respectively.
Notwithstanding, it’s expedient that you acumen your transaction on the description of the pad. Also, you might want to check the policy that backs the prospective products that you’re purchasing.
This would really augment the convenience that you need, at least to give it a try.
Most times, brake pads don’t come with installation manual. However, the accessories that they come with are caliper pins, retaining spring clips, and lubes.
So, before you begin your installation, ensure that all these are made ready. Also, other materials that you’d need for the installation of your brake pad is a car jack, wrench and so on.
Before you even begin the removal of your former brake pad, you would need to pull over and ensure that the automobile is cool first before you begin to disassemble the wheels. Afterwards, you can move over to the next step for the removal of the wheels.
3. Removal of the Wheels
- Put the automobile on gear before you begin to remove the wheels.
- Raise the car up with the car to an altitude that’s best to your preference.
- Use the appropriate wrench to remove the lug nuts from the rails first. Ensure that you remove all the nuts also.
- Once you’re done, remove the wheels from the brake disc. You can even use your steering to position the caliper and the disc to the appropriate position.
- Provided you find difficulty in recognizing the components, then you might want to check out the manual to understand the chassis of the automobile.
4. Removal of Retaining Clips and Old Brake Pads
Retaining spring clips are mostly found on the caliper that’s attached to the brake discs. So, identify the clips and detach it from the caliper pins that hold the pads in place.
Once that’s done, you’d have to remove the pins from the loop, why? Because the pins pass through the aperture that’s close to the chamfer of the bake pad.
So get them removed immediately the retaining clips are removed. After the removal of the brake pads, you can decide what to do with the removed brake pads.
However, most times, it’s used as a tool to determine whether the newly purchased brake pads have the prospect to fit the space.
5. Post Preparation
At this juncture, you’re expected to apply grease to the shim of the brake pads. Once you’ve done that, you’d have to apply grease to the pin that and loops of both the caliper and the brake pads that you intend fixing inside.
Afterwards, use a rod to expand the designated spaces that you want to slot in the brake pads. Nonetheless, please note that it’s expedient that one opt for products that are recommended for the automobile that you’re using.
So once all that is done, and you’ve tested positioning the pads inside their designated positions and it was snug then you can proceed to the next step.
- Align the loops of both the caliper and the brake pads after you had slotted the pads in their respective spaces in the caliper.
- Fix the caliper pins inside the aligned loops and use screwdrivers to drive the nuts that hold them in place.
- Afterwards, use the retaining clip by passing it into the empty hole on the brake pads and attach the residue to the rains on the caliper so as to rigidly fix the brake pads on to the calipers.
- Check it out if you’ve just finished the job successfully.
7. Assembling of the Wheels
Attach the wheels back onto the rails. Position it on the protruded rails just as it was at the initial. Afterwards, use the lug nut to hold the wheels in place.
Of course, use the appropriate wrench in tightening the lug nuts onto the rails. You can check out whether the wheel is tightened already onto the automobile by checking the wheels’ balance.
Once you’re done, remove the car jack after you had returned the position of the car to its former state.
While you’re attaching the brake pads, ensure that the shims are on the inside. Also, test the wheel and the gracing system to see whether there are changes. So, peradventure you do it properly, you can always repeat these steps.
I hope that by the end of this article, you’ve been able to understand how to install retaining clips with brake pads on automobiles.
Of course, the tips are reliable to imbibe and you can practice them with ease. The piece is just easy to comprehend. It’s just the resource that you need, trust me.